background image

7

COMPLY WITH THE DIMENSIONS

(mm)

A

B

C

D

E

F

1F-2F (30)

282

482

59

59

100 min

70 min.

TECHNICAL INFORMATION FOR

THE INSTALLER

Installation,  adjustments  of  controls  and
maintenance  must  only  be  carried  out  by  a
qualified engineer.
The  appliance  must  be  correctly  installed  in
conformity  with  current  law  and  the
manufacturer's instructions.
Incorrect  installation  may  cause  damage  to
persons,  animals  or  property  for  which  the
Manufacturer  shall  not  be  considered
responsible.
During  the  life  of  the  system,  the  automatic
safety  or  regulating  devices  on  the  appliance
may only be modified by the manufacturer or by
his duly authorized dealer.

3) INSTALLING THE COOKTOP

Check that the appliance is in a good condition after
having  removed  the  outer  packaging  and  internal
wrappings  from  around  the  various  loose  parts.  In
case of doubt, do not use the appliance and contact
qualified personnel.

Never leave the packaging materials (cardboard,
bags,  polystyrene  foam,  nails,  etc.)  within
children’s  reach  since  they  could  become
potential sources of danger.

The measurements of the opening made in the top
of  the  modular  cabinet  and  into  which  the  cooktop
will be installed are indicated in either fig. 8. Always
comply  with  the  measurements  given  for  the  hole
into which the appliance will be recessed (see fig. 8
and 9).
The  prospective  walls  (left  or  right)  that  exceed  the
working  table  in  height  must  be  at  a  minimum
distance  from  the  cutting  as  mentionned  both  in  the
columns “E” of the scheme.

The appliance belongs to class 3 and is therefore
subject  to  all  the  provisions  established  by  the
provisions governing such appliances.

INSTALLATION

FIG. 9

FIG. 8

IMPORTANT!
A  perfect  installation,  adjustment  or
transformation  of  the  cook  top  to  use
other  gases  requires  a  QUALIFIED
INSTALLER:  a  failure  to  follow  this  rule
will void the warranty.

Summary of Contents for GD-Z01

















Reviews: