DUDOFF GD-Z01 Installation And User Instructions Manual Download Page 6

6

CLEANING

Note:  continuous  use  could  cause
the  burners  to  change  colour  due  to
the high temperature.

IMPORTANT:
always  disconnect  the  appliance  from  the  gas
and  electricity  mains  before  carrying  out  any
cleaning operation

2) GAS HOB

Periodically  wash  the  hot  plate,  the  enamelled  stell
pan support, the enamelled burner caps “A”, “B” and
“C” and the burner heads "T" (see fig. 6 and 7) with
lukewarm soapy water. They should also be cleaned
plugs  "AC"  and  flame  detection  "TC"  (see  fig.6).
Clean them gently with a small nylon brush as shown
(see  fig.  7/A)  and  allow  to  dry  fully.  Do  not  wash  in
the  dishwasher.  It  is  very  important  to  clean  the
surface  soon  after  every  use,  when  the  glass  is  still
tepid. 
Do  not  allow  vinegar,  coffee,  milk,  salted  water,
lemon or tomato juice from remaining in contact with
the enamelled surfaces for long periods of time.
Do not clean using abrasive metal scourers, powder
abrasives or corrosive sprays.

WARNINGS:
when reassembling the components, observe the
following recommendations:
- check  that  the  holes  in  the  burner  heads  “T”

(fig. 6) are not blocked by foreign bodies.

- Ensure that the enamelled covers “A”, “B” and

“C” (fig. 6 and 7) are correctly positioned on the
burner  head.  The  covers  are  correctly
positioned on the head when they are perfectly
stable.

- If  the  opening  and  closing  of  any  valve  is

awkward,  do  not  force  it  but  request  urgent
intervention  by  the  technical  assistance
service.

- The  pan  support  must  be  placed  in  the

appropriate  centering  pins  (Or  on  the
aluminium  profile  if  present).  Verifying  the
perfect stability. 

-  To  prevent  difficulties  with  lighting,  regularly

clean  the  ignition  elements  (ceramic  and
electrode) and safety cut-off devices (fig.7/A).

- Do not use jets of steam to clean the appliance.

IMPORTANT:

when  removing  the  burners  to  clean  them,  ensure
that all parts are correctly positioned before relighting
them.

FIG. 6

FIG. 7/A

FIG. 7

Summary of Contents for GD-Z01

















Reviews: