manualshive.com logo in svg

DT SWISS D 232, Technical Manual

Share
Download
DT SWISS D 232 Technical Manual Download Page 39

D 232 - Technical Manual V2020.05

39

7.4  FITTING THE SEAT POST
MOUNTING THE SEAT POST IN THE BIKE FRAME

1. 

Hook the shift cable into the Quickconnector.

2. 

Pull the quickconnector downwards and insert 

the cable housing.

3.  Open the seat post clamp, push the seat post 

carefully into the bike frame while pulling the 

cable out of the frame at the same time.

4.  Close the seat post clamp.
5. 

If available, clamp the cable housing with the 

cable clamps of the bike frame.

6. 

Tension the cable by turning the cable 

adjuster on the remote lever.

MOUNTING THE REMOTE LEVER ON THE HANDLEBARS

1. 

Using a 3 mm hex key loosen the fixing screw 

on the clamp and attach the remote lever on 

the desired side of the handlebars.

2. 

Tighten the fixing screw with a max. tightening 

of 5 Nm. 5 Nm an.

 

→ If the remote lever is fitted on carbon 

handlebars, the maximum torque 

may be lower. Observe the handlebar 

manufacturer’s user manual!

Summary of Contents for D 232










































Reviews:

No comments

Brands by name

Popular brands

Load more brands