manualshive.com logo in svg

DT SWISS D 232, Technical Manual

Share
Download
DT SWISS D 232 Technical Manual Download Page 17

D 232 - Technical Manual V2020.05

17

6.  SMALL SERVICE

A small service can be carried out without removing the seat post from the bike frame and without 

removing the saddle.
A small service should be carried out in the following cases:

• 

Interval for a small service has elapsed (50 operating hours).

• 

Malfunctions (see also “5. Trouble Shooting” on page 

14

), e.g.

• 

Seat post does not compress or extend properly

• 

Seat post does not lock correctly in the upper / lower position

• 

Seat post releases without pushing the remote lever downwards / upwards

• 

Seat post makes noises while riding

• 

Shift cable runs sluggishly / high actuating forces on remote lever / shift cable blocked

Preparatory Steps

Make sure that the seat post is in the extended position. If not, extend the seat post by pressing the 

remote lever.
Clean the seat post.

Check all functions of the seat post.

 

If malfunctions occur, observe the information in the table in chap. “5. Trouble Shooting” on page 

14

!

Required Material

Specification

Quantity

universal grease

Slick Honey

as required

cleaners

Motorex Rex, Motorex Swissclean, Motorex OPAL 2400, 

OPAL 3000, OPAL 5000 or similar

as required

6.1  REMOVING THE SEAT POST

1. 

Press the saddle down slightly and unscrew the lock nut from the slider tube by hand.

Summary of Contents for D 232










































Reviews:

No comments

Brands by name

Popular brands

Load more brands