DT SWISS D 232 Technical Manual Download Page 15 | Manualshive

Page: 15 / 41

DT SWISS D 232 Technical Manual Download Page 15

D 232 - Technical Manual V2020.05

15

Issue

Reason

Solution

seat post does not lock

correctly in the upper

position.

or / and
seat post releases without

pushing the remote lever

down.

dirty / too little grease

small service

cable tension too high

reduce the tension of the cable

tension of the actuating spoke

on the quickconnector too high

reduce tension of the actuating

spoke.

“Mounting the

Quickconnector” on page 34

.

release piston jammed

disassemble the seat post

completely, clean all parts.

replace

latch system kit

.

wear of the locking mechanism

coil spring defective

small service and exchange of the

coil spring

seat post does not lock

correctly in the lower

position.

or / and
seat post automatically

releases upwards.

seat post has not locked

correctly because there is not

enough force on the seat post

when lowering

compress with more force until the

mechanical stop

dirty / too little grease

small service

cable tension too high

reduce the tension of the cable

tension of the actuating spoke

on the quickconnector too high

reduce tension of the actuating

spoke.

“Mounting the

Quickconnector” on page 34

.

release piston jammed

disassemble the seat post

completely, clean all parts.

replace

latch system kit

.

wear of the locking mechanism

wear of the locking groove in the

slider tube

disassemble the seat post

completely, clean all parts.

replace

slider tube kit

.

O-ring (“2. Overview” on

/ No. 13) crushed /

defective

disassemble the seat post

completely, clean all parts.

replace

.

axial play of the slider tube in

one or both locking positions

cable tension too high

reduce the tension of the cable

tension of the actuating spoke

on the quickconnector too high

reduce tension of the actuating

spoke.

“Mounting the

Quickconnector” on page 34

.

strong rotational play of the

slider tube

wear of the guide key

disassemble the seat post

completely, clean all parts.

replace

slider tube kit

.

wear of the locking groove in the

slider tube

«
...
13
14
15
16
17
...
»

Summary of Contents for D 232










































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands