Drucker Diagnostics 614VET Operator'S Manual Download Page 3

Page | 3 Drucker Diagn1-814-692-7761 - [email protected]

 

WARNING: For the safety of both the operator and service personnel, care 

should be taken when using this centrifuge if handling substances that are 

known to be toxic, radioactive or contaminated with pathogenic 

microorganisms. When Risk Group II materials are used, (as identified in 

the World Health Organization “Laboratory Bio-Safety Manual”), a Bio-

Seal should be employed. The Bio-Seal accessory for the model is the non-

aerosol shield cap with appropriate tube holders (contact Drucker 

Diagnostics to purchase). In the event that materials of a higher risk group 

are being used, more than one level of protection must be provided. 

 

The use of flammable or explosive materials as well as those materials 

which have a vigorous chemical reaction is prohibited. 

 

For your safety and the durability of your machine, never transport or 

store centrifuge with tube holders inside machine. 

M

ODEL 

D

ESCRIPTION

 

The Model 614VET is a continuous-duty, electronically controlled Fixed 

Angle centrifuge with a lid safety interlock system. The unit is controlled 

by an electronic push–button timer that has been preset for two (2) 

minutes, for precise spin times and ease of use. Samples can be safely 

viewed through the transparent lid. Entry into the machine is restricted 

during operation by the safety interlock system. The Model 614VET 

features a lighted control panel that displays the status of the machine, 

easily viewable from a distance. 

I

NTENDED 

U

SE

 

General purpose laboratory centrifuge, intended for the density-based 

separation of fluids through centripetal acceleration. 

 

Users should also comply with the specimen receptable manufacturer’s 

specific instructions for use, in addition to any other protocols established 

by the testing organization. 

 

This centrifuge is intended to be used exclusively for veterinary use and 

should not be used in any non-veterinary applications. 

W

ARRANTY

 

Drucker Diagnostics warranties that this centrifuge is free from defects in 

workmanship and parts for 2 years. 

 

Summary of Contents for 614VET

















Reviews: