DRS DRS-M210-V2 Manual Download | Manualshive

Page: 7 / 27

background image

Parachute Manual DRS-M210-V2

©2020 Drone Rescue Systems

7/27

5

Installation

Unmount all propellors and detach all batteries and other power supplies before
starting the installation!

Mounted propellors may cause any injuries or damages.
It is mandatory to verify the correct operation with an assembly test right
after the installation! See chapter 5.6 Assembly test for details.

Install the mounting plate

The

will be mounted on the top of the UAV. Therefore, take four

and place each one on one upward Gimbal mounting position. Put the

on the

and fixate it with the

as shown in pictures

below.

Upward Gimbal

Mounting Position

Copyright DJI Technology Co., Ltd

«
...
5
6
7
8
9
...
»

Summary of Contents for DRS-M210-V2




























Reviews:

No comments

Related manuals for DRS-M210-V2

Brand: UnderCover Pages: 16

Brand: Safco Pages: 6

iVu Plus BCR Gen2 Series

Brand: Banner Pages: 12

Brand: Banner Pages: 28

Brand: Banner Pages: 155

Brand: Banner Pages: 64

Brand: Banner Pages: 8

Brand: Banner Pages: 2

Brand: Banner Pages: 8

Brand: Banner Pages: 12

Brand: Jeep Pages: 7

Brand: Vello Pages: 12

Brand: Karma Pages: 7

Brand: Kampmann Pages: 36

Brand: Navibe Pages: 8

1306 RAPID SYSTEM

Brand: Thule Pages: 8

Brand: Woody Valley Pages: 15

Brand: Katranji Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands