background image

18 

A comparison table is provided between the classification of NLGI lubricants (National 

Lubricating Grease Institute) and the ASTM classification (American Society for Testing and 

Materials) for greases for the values that concern the pump. 

For further information about the technical specifications and the safety measures to adopt, 

refer to the product safety sheet (Directive 93/112/EEC) relative to the type of lubricant 

selected and supplied by the manufacturer. 

 

15. GUIDELINES FOR USE 

 

Compliance with the essential safety requirements and the provisions specified in the machine directive was checked by filling 

out prepared check lists that are contained in the technical file. 

Two types of lists were used: 

 

 

Risk assessment (UNI EN ISO 14121-1). 

 

Compliance with the essential safety requirements Machine Directive –EC 06/42). 

 

The risks that were not completely eliminated, but considered acceptable, are specified below: 

 

 

Electrocution: this can only occur in the case of serious user incompetence. 

 

Use of unsuitable lubricant: the types of fluids that are not compatible with correct pump operation are listed below. * 

 

Contact with harmful fluids. 

 

 

FLUIDS THAT ARE NOT PERMITTED 

FLUIDS 

RISKS 

Lubricants with abrasive additives 

wear of the components inside the pump 

Lubricants with silicone additives 

Pump seizure 

Petrol – solvents – inflammable liquids 

Fire – explosion – damage to the gaskets 

Corrosive products  

Pump corrosion - damage to people 

Water 

Pump oxidation 

Food substances 

They would be contaminated 

* For more detailed information regarding product compatibility with particular fluids, contact the Dropsa S.p.A. technical office

 

 

 

 

 

GREASES

 

NLGI 

ASTM 

000 

445 – 475 

00 

400 – 430 

355 – 385 

310 – 340 

265 – 295 

 

Summary of Contents for 2487000



















Reviews: