background image

 

3

GENERAL INFORMATION : 

 
 

The  ULTRA  FLAME  DIRECT  VENT  GAS  STOVE  is  a  high-efficiency  free-standing    gas 
appliance with a maximum  input rating of 30 000 Btu/h with natural gas or 26,000 Btu/h with 
propane.  It  features  a  thermostatic  modulating  valve  and  a  constant  pilot.    This  means  that  the 
flame will vary in height according to room temperature. The colder the ambient temperature the 
larger the flames. The valve is also independent of any exterior electrical supply. Your appliance 
will therefore continue to heat your house in the event of a power failure. 
 
For  increased  efficiency,  we  have  included  a  140  CFM  blower  with  speed  control  and thermo-
switch. Your fan will therefore turn itself on or off automatically, if you desire.  
 
Read  these  instructions  and  consult  your  local  building  authorities  before  installing  this 
appliance. Install the unit and its venting system only as described in these instructions. 
 

 

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE 
 

 

This gas stove has been tested by WARNOCK HERSEY according to the CAN-CGA-2.22M82_   
INTERIM #41 and engineering buletin #68 for Canada and ANSI Z21,50, 50A, 50B for USA. 
 
It is mobile home approved. 
 
The unit can be installed in a range of altitude from 0 to 4 500 ft (0-1 370 m). 
 
This appliance must be connected to a venting system. 
 
Use only with Drolet direct vent kit, supplied by manufacturer. 

Summary of Contents for ULTRA FLAME






























Reviews: