DriSteem MP Installation, Operation And Maintenance Manual Download Page 27 | Manualshive

Page: 27 / 32

background image

25

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Replacing Ultra-sorb Model MP dispersion tubes

MAINTENANCE

REMOVING A DISPERSION TUBE FROM AN ULTRA-SORB PANEL

A dispersion tube may need to be removed for access to an adjacent coil, or
because of tube damage or upgrade to an insulated tube. See page 3 for
how to install a dispersion tube.

1. Apply soapy water around the tube grommet to ease turning and removal

of the dispersion tube.

2. Loosen the jam nut from the tube nut at top of the tube. Rotate the tube off

the top frame assembly bolt (about 4 rotations of the tube).

3. Press downward on the tube so to clear bolt at top of frame.
4. Move the tube to a slight angle so that it does not interfere with top frame

of Ultra-sorb Model MP panel.

5. Pull the tube out from the rubber grommet.
6. If the grommet shows any sign of wear or damage, replace it before

reinstalling the dispersion tube. See Table 29-1 for replacement parts.

Note:

Grommets are provided with replacement tubes.

«
...
25
26
27
28
29
...
»

Summary of Contents for MP

































Reviews:

No comments

Related manuals for MP

CE-CF0.3BD/N3-F

Brand: Midea Pages: 9

Brand: Holmes Pages: 2

Brand: happyhaves Pages: 14

Brand: Black & Decker Pages: 22

Brand: Kenmore Pages: 28

Brand: Kenmore Pages: 16

Brand: Kenmore Pages: 16

Brand: Kenmore Pages: 24

Brand: Kenmore Pages: 32

Brand: Kenmore Pages: 15

Brand: Kenmore Pages: 34

Brand: Kenmore Pages: 11

Brand: Kenmore Pages: 16

Brand: Kenmore Pages: 24

Brand: Kenmore Pages: 24

Brand: Kenmore Pages: 30

Brand: Kenmore Pages: 10

Brand: Timberk Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands