DriSteem MP Installation, Operation And Maintenance Manual Download Page 4

Page: 4 / 32

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Field assembly

INSTALLATION

Note: These assembly instructions are for Ultra-sorb Model MP panels shipped

unassembled by request or as required. Panels with unit height more
than 93" (2360 mm) are shipped unassembled.

LAY OUT THE PANEL COMPONENTS

Place the panel components on a large, flat working surface.

ATTACH THE TOP FRAME ASSEMBLY

Span the flanges with the top frame assembly. Align the locating pins on the
flanges and top frame, and insert screws.

TIGHTEN THE FLANGE LOCKNUTS

Torque the eight flange locknuts to 16 ft-lb (22 N-m) at 100 rpm maximum
using a 7/16" deep-well socket.

INSTALL THE DISPERSION TUBES

Note: Do not remove the poly film from the dispersion tubes until after the

panel is installed.

Table 2-1:
Ultra-sorb Model MP components

Component

Qty .

Header assembly

Dispersion tubes

Varies

Top frame assembly

Side flanges

Screws

Varies

Flange locknuts

Header

assembly

Flange

locknut

Left side

flange

OM-7846

Top frame

assembly

Right side flange

Insulation

FIGURE 2-1: ULTRA-SORB MODEL MP COMPONENTS

Dispersion

tube

Locating pins

Summary of Contents for MP

































Search results

Summary of Contents for MP

Reviews:

Related manuals for MP

Brands by name

Popular brands

DriSteem MP, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for MP

Reviews:

Related manuals for MP

Brands by name

Popular brands