DriSteem MP Installation, Operation And Maintenance Manual Download Page 10 | Manualshive

Page: 10 / 32

DriSteem MP Installation, Operation And Maintenance Manual Download Page 10

8

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Selecting the location

INSTALLATION

• Install the Ultra-sorb panel in a location where discharged water vapor will

be absorbed by the airstream.

• Place the Ultra-sorb panel where the air temperature is capable of

absorbing discharged steam without causing condensation at or after the

unit. This will normally be downstream from the heating coil where the air is

warmest.

• Do not place the Ultra-sorb panel in an outside air intake unless the air is

tempered with a preheat coil.

• Do not place the Ultra-sorb panel near the entrance of a high-efficiency

filter. The filter will remove visible moisture and become waterlogged. See

the Caution "Installing the Ultra-sorb panel upstream from filter media" on

• Do not place the Ultra-sorb panel where discharged visible mist will

impinge directly on a metal surface.

DETERMINE HUMIDIFIER PLACEMENT

Dispersed steam must be absorbed into the airflow before it comes in
contact with duct elbows, fans, vanes, filters, or any object that can cause
condensation and dripping.

«
...
8
9
10
11
12
...
»

Summary of Contents for MP

































Reviews:

No comments