background image

12

DRISTEEM GTS HUMIDIFIER INSTALLATION AND OPERATION MANUAL

•  The GTS humidifi er is a Fan Assisted Category I 

(natural draft) Appliance. It is a Class B23 appliance, 
without a draught diverter, with a combustion 
air blower upstream of the heat exchanger. A 
GTS humidifi er with the sealed combustion option is 
a Class C53 appliance. Installations where the vent 
terminates in a side wall of the building, or where the 
overall horizontal run exceeds the overall vertical run, 
require a power venter.

• Maximum 

fl ue temperature under normal operating 

conditions is 205 °C plus ambient.

•  Maximum abnormal-operation fl ue temperature is 

348 °C plus ambient.

•  Flue draft negative pressure greater than 50 Pa may 

cause unacceptable post ignition.

•  Vent piping must be approved for a Category I 

appliance. Do not use more than one type of venting 
per application.

•  Vent terminal must be at least 1 m above  any forced 

air inlet located within 3 m.

•  Do not use vent equipment from more than one 

manufacturer.

•  When connecting the humidifi er to a gas vent or 

chimney, installation must conform to:
–  Local and national directives and regulations for 

the installation of gas-fi red equipment

–  Governing and building codes
–  Vent manufacturer’s instructions

•  When applying the codes, see also the venting 

manufacturer's instructions, the service gas supplier's 
regulations, and the specifi c instructions provided in 
this manual. 

•  Inspect for proper and tight construction. Remove any 

restrictions or obstructions. An existing chimney may 
require cleaning.

•  Do not connect this humidifi er to a chimney fl ue 

servicing a separate appliance designed to burn solid 
fuel.

•  Never connect this humidifi er to a chimney serving a 

fi replace, unless the fi replace opening is permanently 
sealed off.

•  Code prohibits venting into an unlined masonry 

or concrete chimney. If the humidifi er is connected 
to a lined, masonry chimney, the chimney must be 
sized and installed according to the provisions of the 
governing codes.

Venting 

•  Vent connector serving this appliance shall not be 

connected into any portion of mechanical draft 
systems operating under positive pressure.

•  Add insulation to any roof or wall penetration vent 

connector that is exposed to ambient temperatures of 
0 °C or less, especially any application using single-
wall vent pipe as a connector.

•  Do not insulate vent pipe exposed to outdoor weather 

conditions (e.g., above roof lines).

•  Install vent piping as straight as possible, with a 

minimum number of turns or elbows.

•  Maintain a minimum upward slope of 2% on all 

horizontal runs. 

•  Rigidly support the vent pipe every 1.5 m or less with 

hangers or straps to ensure there is no movement after 
installation. The humidifi er vent box should not support 
the weight of the vent piping.

•  No portion of the vent system should extend into, or 

pass through, any circulation air duct or plenum.

•  Install and fi re-stop all vent pipe passing through 

fl oors, ceilings, and walls with the proper clearances 
from combustible material according to local and 
national directives and regulations for the installation 
of gas-fi red equipment.

•  In replacement installation where an existing vent 

system may be used, inspect the vent system for 
condition, size, type of vent material, and height to 
meet the requirements in these instructions. 

CAUTION

 

Flue condensate removal

Install a drip leg or fl ue box condensate drain for start-
up fl ue condensate removal. Failure to follow these 
instructions could cause water to accumulate in the 
fl ue box.

OUTDOOR ENCLOSURE VENTING 

The vertical section of fl ue must be at least 1.5 meters or 
meet all governing codes, whichever is longer. DriSteem 
recommends a drip tee directly after the factory-supplied vent 
connection. DriSteem recommends a high-wind vent cap on 
all GTS humidifi ers. See Figure 4-2.

GENERAL VENTING GUIDELINES 

  

WARNING

 

Installation requirements:

The humidifi er must be installed by a qualifi ed technician and meet the requirements of all governing codes. 
Failure to follow these instructions could cause severe bodily injury or death.

Summary of Contents for GTS-100























Reviews: