Drinkpod 1000 Pro Series Installation Manual Download Page 56

Page: 56 / 67

Installing Your Water 1000 Pro Series

Installing Your Water 1000 Pro Series

2-54

Diagram 2.8.4 -

Open Shutoff Valve

You should hear water running and filling the 1000 Pro Series’s tanks. Check for leaks, and

wait until the sound of water running stops.

Once the 1000 Pro Series is filled, plug it in, but do not flip on the power switches yet.

We need to flush each temperature mode. Start by flushing the

Ambient Mode

into

your large container for 30 seconds. Press the light blue

Ambient Mode Button

to begin

dispensing.

Now, for the best experience, we recommend flushing the full tank capacity for both the

Hot Mode

and

Cold Mode

. For reference, the

Hot Tank

capacity is

0.26 gal (1 liter)

and the

Cold Tank

capacity is

1.1 gal (4.16 liters)

. For directions on how to flush your

appliance, see the included

Use & Care Guide

, or the

Quick Start Sticker

applied to

your Drinkpod 1000 Pro Series’s control panel.

9. If you haven’t connected any accessory appliances to your new

Drinkpod 1000 Pro Series, you are finished!!! You can now proceed to power on your

1000 Pro Series (

see Use & Care Guide for instructions

10. If you have connected accessory appliances, you can now open the

1/4 in. Quick Connect Shutoff Valve(s)

connected to your

Accessory Line

. Water

should now start flowing into your accessory appliances. Check the lines, valve, and

Summary of Contents for 1000 Pro Series




































































Search results

Summary of Contents for 1000 Pro Series

Reviews:

Related manuals for 1000 Pro Series

Brands by name

Popular brands

Drinkpod 1000 Pro Series, Installation Manual

Search results

Summary of Contents for 1000 Pro Series

Reviews:

Related manuals for 1000 Pro Series

Brands by name

Popular brands