Drinkpod 1000 Pro Series Installation Manual Download Page 55

Page: 55 / 67

Installing Your Water 1000 Pro Series

Installing Your Water 1000 Pro Series

2-53

Enabling Water Flow

This is the second to last stage of installation. In this stage, we will enable water flow at each
shutoff valve, one at a time to ensure there are no leaks.

1. If it’s not already open, start by opening your

Water Source Valve

(the valve on your

existing water source we first shut off).

2. If you’re using a

Sink Water Source

, open the valve on

3/8 in. Sink Adapter Valve

(if you haven’t already opened it). Confirm there are no

leaks.

Diagram 2.8.2

- Open Sink Adapter Valve

Ensure nothing is leaking between the last applicable valve above, and the shutoff valve

connected to your

Source Line

Now open the valve on the Quick Connect Shutoff Valve connected to your

Source Line

and

Source Input Port

on your 1000 Pro Series, as shown below.

Summary of Contents for 1000 Pro Series




































































Search results

Summary of Contents for 1000 Pro Series

Reviews:

Related manuals for 1000 Pro Series

Brands by name

Popular brands

Drinkpod 1000 Pro Series, Installation Manual

Search results

Summary of Contents for 1000 Pro Series

Reviews:

Related manuals for 1000 Pro Series

Brands by name

Popular brands