Drinkpod 1000 Pro Series Installation Manual Download Page 21 | Manualshive

Page: 21 / 67

background image

Installing Your Water 1000 Pro Series

Installing Your Water 1000 Pro Series

2-19

connection is almost certainly a ½ in. (Nominal/NPT) fitting. If you have a 15/16 in. and
a 1 in. wrench, you can check to confirm by attempting to loosen the connection (there
is 1/16 in. range of variance between different plumbing fittings).

IF THAT DOESN’T FIT,

you have an extremely rare setup, and should contact a plumber.

IF THE LARGER

WRENCH DOES FIT, we don’t provide 1/2 in. adapter in your kit (only 2.5% of our
customers require it), but we’d be more than happy to ship you one for free upon request.
Call us at

1-844-374-6576

, or email us at

[email protected]

.

Or, if you don’t

want to wait, you can pick one up at your local hardware store. Ask for a

1/2 in (FIP) x

1/2 in. (MIP) x 1/4 in (OD) Push-to-Connect Angle Stop Adapter Valve

.

Diagram 2.3(B).5

Detach Cold Water Feed Line

6. Next, screw the bottom (female) end of

3/8 in. Sink Adapter Valve

to the

top (male) end of

Cold Water Shutoff Valve

using your hand. Then tighten

using medium force with the same wrench (11/16 in.) you used to remove

Cold Water Feed Line

.

«
...
19
20
21
22
23
...
»

Summary of Contents for 1000 Pro Series




































































Reviews:

No comments

Related manuals for 1000 Pro Series

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: A.MENARINI Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Pages: 12

Brand: Hanil Pages: 24

Brand: Hanil Pages: 32

Brand: Hanil Pages: 24

Brand: Xiitech Pages: 6

Synthesis SDEC-3000

Brand: JBL Pages: 24

Brand: Xilica Audio Design Pages: 30

Brand: Waters Pages: 250

Brand: Waters Pages: 141

Brand: Yamaha Pages: 5

Brand: Kärcher Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands