Drill Master 61204 Owner'S Manual And Safety Instructions Download

Page: 6 / 16

Page 6

For technical questions, please call 1-888-866-5797.

Item 61204

SAFET

Op
ERA
TION

AINTENAN

SETU
p

Specifications

Electrical Rating

120VAC / 60Hz / 5.5A

Motor No Load Speed

5000 RPM

Max. Accessory Diameter 6"
Arbor Size

7/8"

Setup - Before Use:

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION:

Release the Trigger and unplug the tool from its electrical outlet before

assembling or making any adjustments to the tool.

Note:

For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Functions

Figure A

Handle

Trigger

Blade

Stationary

Guard

Moveable Guard

Angle Guide

Clamp

Base

3150240

Summary of Contents for 61204

















Search results

Summary of Contents for 61204

Reviews:

Related manuals for 61204

Brands by name

Popular brands

Drill Master 61204, Owner'S Manual And Safety Instructions

Search results

Summary of Contents for 61204

Reviews:

Related manuals for 61204

Brands by name

Popular brands