Dream Maker Spas B6L Series Owner'S Manual Download Page 17

CHEMICAL NOTES

SPA OPERATION / WATER CHEMISTRY continued

2. It is recommended that the spa be drained regularly depending on its size, location and the frequency of use.

3. Clean filter and cartridge periodically according to manufacturer’s instructions.

4. Keep the spa covered when not in use to reduce the loss of heat and to keep our leaves, dirt, and other foreign materials

from settling in the water.

5. Since the water capacity of your spa is far less than that of a swimming pool, the chemical reaction caused by the presence

of one or more persons in the spa is more rapid and pronounced. For these reasons, it is important to frequently check the
bromine level, the pH level and total alkalinity of water then add the prescribed chemicals as necessary to maintain the
proper chemical balances.

6. If questions or doubts arise regarding quantities and timing or chemical applications to your spa, contact your spa dealer

who can assist you in prescribing the correct program for your spa.

7. Store all chemicals in a cool dry place and in such a manner as to prevent contact by children and pets.

8. When adding chemicals to your spa water, add to the center of the spa with the pump operating. Never add chemicals to

unheated water as this will affect chemical action.

15

Summary of Contents for B6L Series



























Reviews: