manualshive.com logo in svg

Dräger Oxylog 2000 plus, Pocket Manual

Share
Download
Dräger Oxylog 2000 plus Pocket Manual Download Page 44

44

Trouble Shooting

Messages in the alarm window 

Alarm

Cause

Remedy

!! High respiratory rate

Patient breathes at a high 

Check patient's condition, check ventilation 

spontaneous rate.

pattern, correct alarm limit 

RRsp

if necessary.

!! Int. battery charging inop

Technical defect. 

Contact your local DrägerService for 

additional support – restricted operation is 

now possible.

!!! Int. battery discharged

The operating time for operation with the 

The ventilator must immediately be reconnected

internal battery has expired and an

to a mains supply, an on-board DC supply 

external DC supply has not been connected.

or a fully charged battery.

!! Int. battery in use

Oxylog 2000 

plus

draws its power from 

Press the 

Alarm Reset

key to 

the internal battery due to the absence of

confirm the alarm.

an external DC supply.

!! Key failed 

Technical defect. 

Contact your local DrägerService for 

additional support – restricted operation is 

now possible.

Summary of Contents for Oxylog 2000 plus





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands