Dräger CPS 6900, Instructions For Use Manual

Page: 24 / 92

24 Dräger CPS 6900
Use
3.5 Type-identical identification mark
The type-identical identification mark is found on the pocket in
the chemical protective suit.
4 Use
4.1 Prerequisites
4.2 Instructions on using the fastener
system
The fastener system has been developed especially for the
chemical protective suits. Generally, the additional seals make
mobility more difficult in comparison to zip fasteners on normal
clothing. To prevent creases in the fastener system, the
protective suit wearer must grasp and pull the fastener system
to the hood, while a second person pulls the trouser leg with
the fastener system down using both hands until the fastener
system is free of creases. The protective suit wearer should be
standing upright when opening and closing the fastener
system.
4.2.1 Opening the fastener system

Fully open the fastener system.

Always pull the zipper tab in the direction of the zipper
mechanism; never pull diagonally!

Do not use force. Zip elements can become bent!

If the zipper tab gets caught, pull it back and push it forward
again.
4.2.2 Closing the fastener system

When closing the fastener system, avoid diagonal forces
on the zip.

Pull the fastener chains together by hand.
Then the zip will slide more easily along the section that is
being pulled together.

Foreign objects, such as shirt, jacket, threads, etc. must
not be trapped between the zip elements.
4.3 Preparation for use
4.3.1 Preparing the chemical protective suit
1. Check for leaks before using the suit for the first time in
order to detect any damage due to transport. Observe the
maintenance intervals thereafter (see Chap. 6.1 on
Page 26).
2. Place the chemical protective suit flat on the ground and
examine visually (see Chap. 6.2 on Page 26).
3. If fitted, check the function of the ventilation unit and the
connection to the compressed air breathing apparatus.
4. Treat the full face mask visor from outside using "klar-pilot"
anti-fogging gel. Use the spray “klar-pilot“ Comfort for
coated mask visors. If the suit is not fitted with an antifog
visor, also treat the inside of the visor.
4.3.2 Putting on the chemical protective suit
1. Put on underclothing (moisture-wicking work clothing,
cotton gloves).
Caution! Strictly follow the Instructions for
Use.
Protective clothing against gaseous, liquid,
aerosol and solid chemicals (according to
EN 943-1:2015, type 1a)
Protective clothing against infective agents
(according to EN 14126:2003+AC:2005,
type 1a-B)
Protective clothing against radioactive
contamination by solid particles (according
to EN 1073-1:2016+A1:2018 and
EN 1073-2:2002 (for classes, see 3.3))
Assignment of height, waist and chest
measurement to the size of the chemical
protective suit (see Chap. 9 on Page 31).
WARNING
The chemical protective suit must be used in
accordance with the applicable standards and
directives of the country in question.
The environmental impact must be determined prior to
use, since the suitability of the chemical protective suit
must be determined before its use. The chemical
protective suit must only be used for suitable
purposes. The user has to consider national and other
requirements for the use of personal protective
equipment.
Non-observance can lead to death or severe physical
injuries.
CAUTION
To avoid damage to the fastener system, both halves
of the zip must be parallel and unstressed. Do not use
force when opening and closing the fastener system or
jerk the zipper.
Fastener systems without sufficient lubrication are
more difficult to operate. This can result in damage to
the fastener system. Lubricate the fastener system
using the grease stick supplied by Dräger.
!
!
NOTICE
Dräger recommends that you keep the flat bags in
which the chemical protective suit was delivered for
later storage purposes.
WARNING
Do not use a damaged chemical protective suit. If you
do, you risk death or serious injury.
NOTICE
Get a second person to assist you with donning the
suit.
NOTICE
Dräger recommends tucking the trouser legs of the
underclothing into the socks to prevent the trouser legs
shifting.
To prevent the cotton gloves slipping down, they
should be fixed on the wrist using insulation tape.
i i
!
i i
i i