Alternative C (supply from mobile compressed air source):
3
Like alternative A
4/11
such as ageing. A and if the compressed air supply hose is not part
of the mobile air source, connect it to the mobile air source
6
n/a
5
Like alternative A
7
n/a
*
activate mobile compressed air source
2
Like alternative A
1
Like alternative A
After use
Leave hazard area.
1
Remove full-face mask
1)
.
4
Disconnect compressed air supply hose:
Firmly press both coupling halves together and pull back outer sleeve
at same time until coupling disengages. Fit caps.
3
Undo waist belt.
Take off apparatus and turn off compressed air supply.
Maintenance and care
See "Maintenance intervals".
Clean, disinfect and dry mask.
For breathing hose:
Clean:
Must be cleaned after every use. Do not use solvents, such as acetone,
alcohol, etc. Clean with lukewarm water containing the all-purpose detergent
Sekusept Cleaner
2)
and a cloth. Then allow to dry at room temperature.
Check correct functioning and absence of leaks
Assemble compressed air line breathing apparatus as described for
mask
and breathing hose.
Start up compressed air supply system and check operating pressure
(required: 7 - 10 bar) adjust if necessary.
Brush the connections and screw connections with soapy water
when at operating pressure. No bubbles should form. Tighten seals
if necessary.
Function test:
The excess valve is integrated in the breathing hose which connects
the ABIL-R1/ABIL-R2 with the half or full face mask.
Close the control valve and seal the excess valve. A low volumetric
air flow must be noticeable.
Open the control valve completely. A high volumetric air flow must be
noticeable.
Storage
All parts must be stored in a dry, cool and dust-free place where they cannot be
deformed. Keep away from direct light and heat.
Observe ISO 2230 and national regulations for the storage, maintenance and
cleaning of rubber products.
Technical data
Troubleshooting
Maintenance intervals
1)
Note the associated instructions for use.
2)
Made by Messrs. Henkel Hygiene GmbH, D-40554 Düsseldorf, Germany.
Note the associated Instructions for Use
Compressed air hose
Max. length 3 m
Compressed air supply hose
Max. length 50 m,
antistatic, heat-resistant
Respiratory air
As per EN 12 021
Do not use oxygen or
oxygen-enriched air.
Operating pressure
7 - 10 bar
Temperature in use
–10 °C to 60 °C,
refer to "Use"
Volumetric air flow
Min.
300 litres per minute
Max.
1000 litres per minute
Fault
Cause Remedy
Unpleasant taste
Respiratory air does not
conform to EN 12021
Check all filters and
replace and smell if
necessary
No air
Cylinder valve closed
Open cylinder valve
Couplings not closed
Check couplings
Hose jammed
Check hoses
Air flow too low
Control valve turned
down
Open control valve
Operating pressure too
low
Set operating pressure
Hose too long
Check hose length
Filter contaminated
Replace filter
Air flow too high
Control valve open wide Turn control valve down
Operating pressure too
high
Set operating pressure
Equipment
item
Work required
Before each use
After each use
Half-yearly
Y
early
Every 6 years
Full-face mask
1)
and breathing
hose
1)
Note the associated instructions for use.
Clean, disinfect, dry
X
Couplings
Use a test gauge to check the
plug-in coupling for wear
Check that the couplings are
free-moving
X
X
Complete
compressed air
line breathing
apparatus
Clean outside
Rinse inside with air
Check correct functioning and
absence of leaks
X
X
X
X
X
Compressed air
cylinder
Charge
Check charging pressure
Expert testing
X
X
X
2)
2)
e.g. by Dräger Safety
Pressure
reducer
Replace high-pressure
gaskets
General overhaul
X
2)
X
2)
Fine
compressed
air filter
Replace filter cartridge
X
3)
3)
Only if there is a smell of oil.
X
