background image

10

 

        

DR

® 

48" LANDSCAPE RAKE

 

Chapter 4: Maintaining The DR 48" LANDSCAPE RAKE 

Regular maintenance is the way to ensure the best performance and long life of your machine.  Please refer to this Chapter for 
maintenance intervals and procedures. 

Regular Maintenance Checklist 

P

ROCEDURE

 

B

EFORE 

E

ACH 

U

SE

 

Check general equipment condition e.g., Nuts, Bolts, welds, etc. 

 

Hose down the DR LANDSCAPE RAKE 

 

Check the Tire Pressure 

 

Check condition of Tines 

 

Cleaning the DR Landscape Rake

 

1.

 

Use a Hose or Pressure Washer to clean the DR Landscape Rake to keep the Tines, Transport Wheels etc. clean and clear of 
debris. 

Checking the Tire Pressure 

Tools and Supplies Needed: 

 

Tire Pressure Gauge 

 

Air Compressor 

1.

 

Remove the Valve Stem Protective Cap (Figure 10) and check the tire 

pressure with a Tire Pressure Gauge. 

2.

 

Check what the manufacturers recommended pressure is that is stamped on 
the side of the Tire. 

3.

 

If the pressure is too low, add air through the Valve Stem with an air hose. 

4.

 

Replace the Valve Stem Protective Cap when finished. 

5.

 

Repeat for both Wheels. 

Replacing the Tines 

Tools Needed: 

 

17mm Wrench 

1.

 

Use a 17mm Wrench to remove the Carriage Bolt and Locknut that secures 
the Tine (Figure 11). Slide the Tine out of the Tine Pressure Plate. 

2.

 

Slide the replacement Tine into the Tine Pressure Plate and re-secure with 
the Carriage Bolt and Locknut. 

3.

 

Repeat for all damaged or worn Tines. 

Tines 

Tines 
Pressure 
Plates 

Carriage 
Bolts and 
Locknuts 

Tine 
Frame 

Figure 11 

Valve 
Stem Cap 

Figure 10 

Before performing any maintenance, you must first shut off the tow vehicle, remove the key and set the parking brake. 

Do not over inflate the tires. Inflate to the manufacturers recommended 
pressure found on the tires. 

Summary of Contents for 48" LANDSCAPE RAKE

















Reviews: