manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual

Share
Download
Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 310

310 XML API basetype properties

inband-ses

string

•

Disabled

: The in-band SES interface is disabled.

•

Enabled

: The in-band SES interface is enabled.

inband-ses-

numeric

uint32

Numeric equivalents for 

inband-ses

 values.

•

0: Disabled

•

1: Enabled

activity-

progress

string

•

Enabled

: Access to the activity progress interface via HTTP port 8081 is 

enabled. This mechanism reports whether a firmware update or partner 

firmware update operation is active and shows the progress through each 

step of the operation. In addition, when the update operation completes, 

status is presented indicating either the successful completion, or an error 

indication if the operation failed.

•

Disabled

: Access to the activity progress interface via HTTP port 8081 is 

disabled.

activity-

progress-

numeric

uint32

Numeric equivalents for 

activity-progress

 values.

•

0: Disabled

•

1: Enabled

management-mode

string

Not applicable.

management-

mode-numeric

string

Not applicable.

Table 58

security-communications-protocols properties (continued)

Name

Type

Description

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands