Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 278

Page: 278 / 363

278 XML API basetype properties

fan

This basetype is used by

show fans

and

show power-supplies

Table 36

fan properties

Name

Type

Description

durable-id

string

Fan unit ID in the form

fan_

enclosure-ID

fan-number

name

string

Fan unit name in the form

Fan loc:

position

-PSU

power-supply-ID

The position is as viewed from the back of the enclosure.

location

string

Fan location in the form

Enclosure

enclosure-ID

position

. The

position is as viewed from the back of the enclosure.

status-ses

string

Fan status.

•

Unsupported

•

Critical

•

Warning

•

Unrecoverable

•

Not Installed

•

Unknown

•

Unavailable

status-ses-

numeric

uint32

Numeric equivalents for

status-ses

values.

•

0: Unsupported

•

1: OK

•

2: Critical

•

3: Warning

•

4: Unrecoverable

•

5: Not Installed

•

6: Unknown

•

7: Unavailable

extended-status

uint32

A numeric value that provides additional information to supplement the standard

SES status shown by the

status

and

status-numeric

properties. The

extended-status

value is a bitwise value computed from the values of five

status bits, and may be one of the following values or a combination of these

values.

•

: The fan has reported a failure.

•

: The fan is off.

•

: The fan FRU is not installed.

•

: The fan status cannot be determined.

•

: The fan is requested to be on (not off). This is the default status and

represents normal operation.

•

: Fan has failed.

•

: Fan is off.

•

: Fan has failed and is off.

•

: Fan status is unknown, which could represent an I

C communication

issue.

status

string

Fan unit status.

•

Error

•

Off

•

Missing

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Search results

Summary of Contents for AssuredSAN 6004

Reviews:

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual, Page: 278 / 363

Search results

Summary of Contents for AssuredSAN 6004

Reviews: