manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual

Share
Download
Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 225

advanced-settings-table 225

partner-notify-

numeric

uint32

Numeric equivalents for 

partner-notify

 values.

•

0: Disabled

•

1: Enabled

auto-write-back

string

Shows whether the cache policy will change from write-through to write-back 

when the trigger condition is cleared.

•

Disabled

: Auto-write-back is disabled.

•

Enabled

: Auto-write-back is enabled. This is the default.

auto-write-

back-numeric

uint32

Numeric equivalents for 

auto-write-back

 values.

•

0: Disabled

•

1: Enabled

disk-dsd-enable

string

Shows whether available disks and global spares will spin down after a period 

of inactivity shown by the 

disk-dsd-delay

 property.

•

Disabled

: Drive spin down for available disks and global spares is 

disabled. This is the default.

•

Enabled

: Drive spin down for available disks and global spares is 

enabled.

disk-dsd-

enable-numeric

uint32

Numeric equivalents for 

disk-dsd-enable

 values.

•

0: Disabled

•

1: Enabled

disk-dsd-delay

uint16

Specifies the period of inactivity in minutes after which available disks and 

global spares will spin down, from 1 to 360 minutes. The value 0 means spin 

down is disabled. The default is 15 minutes.

background-

disk-scrub

string

Shows whether disks that are not in vdisks are automatically checked for disk 

defects to ensure system health. The interval between background disk scrub 

finishing and starting again is 72 hours.

•

Disabled

: Background disk scrub is disabled. This is the default.

•

Enabled

: Background disk scrub is enabled.

background-

disk-scrub-

numeric

uint32

Numeric equivalents for 

background-disk-scrub

 values.

•

0: Disabled

•

1: Enabled

managed-logs

string

Shows whether the managed logs feature is enabled, which allows log files to 

be transferred from the storage system to a log-collection system to avoid losing 

diagnostic data as logs fill.

•

Disabled

: The managed logs feature is disabled. This is the default.

•

Enabled

: The managed logs feature is enabled.

managed-logs-

numeric

uint32

Numeric equivalents for 

managed-logs

 values.

•

0: Disabled

•

1: Enabled

single-

controller

string

For a 2U14 or 2U24 system that had two controller modules but now has only 

one and is intended to be used as a single-controller system, this property shows 

whether the operating/redundancy mode is set to Single Controller. This 

prevents the system from reporting the absent partner controller as an error 

condition. This parameter does not affect any other system settings. Installing a 

second, functional controller module will change the mode to Active-Active ULP.

•

Enabled

: Single Controller mode is enabled.

•

Disabled

: Single Controller mode is disabled.

Table 8

advanced-settings-table properties (continued)

Name

Type

Description

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands