manualshive.com logo in svg

Dot Hill Systems AssuredSAN 6004, Cli Reference Manual

Share
Download
Dot Hill Systems AssuredSAN 6004 Cli Reference Manual Download Page 279

fan 279

status-numeric

uint32

Numeric equivalents for 

status

 values.

•

0: Up

•

1: Error

•

2: Off

•

3: Missing

speed

uint32

Fan speed (revolutions per minute).

position

string

Fan position, as viewed from the back of the enclosure.

•

Left

•

Right

position-

numeric

uint32

Numeric equivalents for 

position

 values.

•

0: Left

•

1: Right

serial-number

string

•

(blank): Not applicable.

fw-revision

string

•

(blank): Not applicable.

•

Firmware revision of a fan FRU.

hw-revision

string

•

(blank): Not applicable.

locator-led

string

Shows the state of the locator LED on a fan unit.

•

Off

•

On

locator-led-

numeric

uint32

Numeric equivalents for the 

locator-led

 property.

•

0: Off

•

1: On

health

string

•

OK

•

Degraded

•

Fault

•

N/A

•

Unknown

health-numeric

uint32

Numeric equivalents for 

health

 values.

•

0: OK

•

1: Degraded

•

2: Fault

•

3: N/A

•

4: Unknown

health-reason

string

If Health is not 

OK

, the reason for the health state.

health-

recommendation

string

If Health is not 

OK

, the recommended actions to take to resolve the health issue.

Table 36

fan properties (continued)

Name

Type

Description

Summary of Contents for AssuredSAN 6004












































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands