2
P/N 731.018 Rev I • 05/18
©
copyright 2008-2018
dormakaba
ComboGard Pro locks can either be configured using the
ComboGard Pro Setup software or through a series of
keypad commands. This document will cover configuring the
lock using both methods.
The ComboGard Pro Lock has three states of operation:
Factory Default, Manual Setup
, and
Active
. ComboGard
Pro locks are shipped from LA GARD in Factory Default
state without Users or features enabled.
Factory Default:
The Lock must be in the Factory Default
state to be programmed by the PC software.
Factory mode functions as follows:
•
1
key – When pressed, will open the Lock.
•
0
key – When pressed, prompts the ComboGard Pro Setup
software to send the configuration settings to the Lock.
OR
if pressed and held, places the Lock into Manual Setup.
• All other keys perform no function.
Manual Setup:
The Lock can be configured using the
keypad only.
Active:
To activate the Lock and freeze the configuration,
the Manager combination MUST be changed.
PROGRAMMABLE LOCK FEATURES
MODES
(Multiple Modes may be selected.)
•
Silent Alarm
(Alarm Box Required - P/N 2789NC)
If enabled, this option will send a signal to an outside
alarm system through the LA GARD Alarm Box.
•
Dual Mode
In Dual Mode, two combinations are required to open the
lock. Manager Commands 1,2,3,7 and 9 can be performed
using the Manager combination alone.
In “Dual Mode and [User + Manager] to access Manager
Menu”, two combinations are required for all lock functions
except to Change Combination. A valid User combination
must be entered first, followed by the Manager
combination to access Manager Commands 1,2,3,7 and 9.
•
Time Delay Override
If enabled, User 9 can override delay period.
User 9 must be active.
EXTERNAL SIGNALS
(Alarm Box Required - P/N 2789NC.
Only one External Signal type may be selected.)
An external input signal to the Alarm Box will either disable
the Lock from opening, override the time delay, or enable the
remote override depending on the selection programmed for
External Signals.
• External Signal disables Lock opening with valid
combination.
OR
External Signal overrides Time Delay. (This option is
ONLY available if enabled using Setup software.)
OR
External Signal enables the Remote Override. (This
option is ONLY available if enabled using Setup software,
and with Lock code level 39E v1.09 or higher.
)
TIME DELAY
• Delay Period 1 - 99 minutes
• Open Period 1 - 19 minutes
NOTE:
If the Time Delay On is not selected, then this
feature is inactive. This feature may be enabled later.
(Refer to Manager Instructions 732.018.)
COMBINATION LENGTH
A combination length from six (6) to nine (9) digits may be
selected.
NOTE:
To maintain the VdS Class 2 and EN 1300 Class
B certification when the duress alarm feature is used, a
combination length of 7 digits or longer must be selected.
LOCK USERS
Manager
• Open Lock
• Change Combination
• Enable/Disable Users
• Delete Users
• Set Time Delay Values
• Audit Lock
Up to 9 Users
• Open Lock
• Change Combination
STANDARD LOCK FEATURES
Wrong Try Penalty
• Entry of four (4) consecutive invalid combinations initiates
a five (5) minute delay penalty.
• Lock responses during the penalty period are as follows:
- The LED will flash every ten (10) seconds.
- If any key is pressed, the Lock will flash the LED and
beep three times.
• Once the penalty period has ended, two (2) consecutive
invalid combinations will initiate another five (5) minute
penalty period.
Low Battery Warning
• Repeated audio/visual signals (LED flashes/beeps) during
Lock opening indicate the battery is low and should be
replaced immediately.
• If the battery level becomes too low to safely operate the
Lock, pressing any key will initiate the low battery
warning. The battery must be replaced before the Lock
will operate.
Audit Records
• Lock records the last 63 events in non-volatile memory.
• Audit file cannot be deleted from the Lock.
• Only the Manager can audit the Lock.
• ComboGard Pro auditing software and an Interface
Adapter are required to retrieve a Lock audit.
