background image

3  HARDWARE INSTALLATION

 

46 | WQXM-PG Wi-Q™ Gateway Setup and User Guide

3.2.7.3.2 Troubleshooting the WAC/SDC

LED Lights

Sounder

Try

Single Red Flash --------

Use the card at a moderate 
speed.

Red Flashes 

3 short tones

Use the temporary operator 
card provided with the lock,
OR
perform a deep reset to 
restore to the factory de-
fault settings. (The lock may 
already be associated/pro-
grammed.)

Green Flashes

--------

Check the motor connection 
on the Omnilock.

Green and Red 
Alternating 
Flashes

--------

Check the motor connection 
to the WDC Board as well 
as the harnesses. Verify all 
connections are tight. 

For additional troubleshooting instructions, see the service manual 
for the hardware components and assemblies.

Once the installed controllers have been tested, they are ready to 
be signed into LP4502 or ACS. To do this, the ACS must be in-
stalled on the host computer or the LP4502 configured and com-
municating with the ACS as well as the WQXM-PG Gateways. At a 
minimum, the segment should be created and the Gateways online 
and communicating to the ACS or the LP4502 Mercury Controller 
Board. For more information see the “Configure Gateways (Task 
4)” section on page (

26

). 

3.2.7.3 Troubleshooting the Controllers

3.2.7.3.1 Troubleshooting WDC and Omnilock Locks

If the mechanism doesn’t unlock, refer to the following table:

LED Lights

Sounder

Try

Single Red Flash --------

Use the card at a moderate 
speed.

Red Flashes 

3 short 
tones

Use the temporary operator card 
provided with the lock,
or 
perform a deep reset to restore 
to the factory default settings. 
(The lock may already be associ-
ated/programmed.)

Green Flashes

--------

Check the motor connection on 
the Omnilock.

Green and Red 
Alternating 
Flashes

--------

Check that the motor connection 
is secured on the WDC at the 
connector between the wiring 
harnesses and at the controller 
board.

Summary of Contents for BEST Wi-Q WQXM-PG




















































Reviews: