background image

dormakaba 8300/F8300 Exit Device Installation Instructions

95011759 (1135-30) I8300-15

06-2020

Exit Device

7

Install strike

Options: cylinder dogging

1.9  Install strike

1.9.1  Install strike and adjust if 

necessary. Center line of strike 
must line up with horizontal 
reference line on door. Refer to 
carton label for strike number.

A. For strikes 486 & 443:

• 

Wood jamb: No. 31 drill 3/4” [19] 
deep

• 

Metal jamb: No. 21 drill-tap 
10-32

B. For strikes 463, 319 or 320:

• 

Wood jamb: No. 25 drill 1” [25] 
deep

• 

Metal jamb: No. 14 drill-tap 
12-24

CL

NOTE: BACKSET OF DEVICE SHOWN FOR 5/8” 
[16] HEIGHT STOP.

1.10  OPTIONAL: Cylinder dogging

2-1/16” [53]

2-1/16” [53]

1-3/8” [35]

1-5/8” [41]

No. 463

No. 486

No. 443/425

No. 319/320

1.10.1  Thread mortise cylinder into touch bar 

assembly (see above)

1.10.2  Snug (1) #4-40 x 7/16” set screw with 

allen wrench (DO NOT OVER TIGHTEN)

1.10.3  Depress touch bar and turn key clockwise to 

dog and counter clockwise to release.

NOTE: CYLINDER MUST BE INSTALLED WITH TOP 
OF CYLINDER AWAY FROM CHASSIS (See above)

3/64” [1] allen wrench

#4-40 x 7/16” [11] 

set screw

Touch Bar Assembly

dormakaba cylinder 

supplied #90X10SC118

Cam Detail 

dormakaba #10

Minimum/maximum 

lock cylinder height

3/4”

[19]

min.

5/16”

[8] to

11/32”

[9]

1”

[25]

min

1-1/8”

[29]

max

spacer ring

(when req’d)

Summary of Contents for 8300 Series









Reviews: