manualshive.com logo in svg

DONPER BH7480, User Manual

Share
Download
DONPER BH7480 User Manual Download Page 36

DONPER 

USA

—USER MANUAL 

36  — COPYRIGHT DONPER USA 2015 

Mix is too soft. 

1. Mix in the freezing cylinder is 
too warm. 
2. The mix is aged or over- agi-
tated. 
3. Not enough space around 
the machine or obstructions 
around the machine that pre-
vent proper air flow for the re-
frigeration system to cool 
properly.  
4. Worn scraper blades. 

1. Increase the firmness 
level setting (higher num-
ber). 
2. Replace old mix with 
fresh product. 
3. Space machines 
properly to allow for ade-
quate air flow across the 
condenser (8” in between 
machines and 12” behind 
each machine is optimal). 
4. Check scraper blades 
for signs of wear. Replace 
if there is any damage or if 
they are unevenly worn. 
5. Clean the condenser to 
allow better air flow. 

Make 

sure that the machine un-
plugged before removing 
the back panel to clean 
the condenser. 

The mix in the hop-
per is too cold. 

1. The temperature setting on 
the thermostat needs adjust-
ment. 
2. Faulty thermostat. 

1. Adjust hopper thermo-
stat temperature. 
2. Call the Donper USA 
service line to have ther-
mostat inspected/
replaced. 

The mix in the hop-
per is warm. 

1. The temperature setting on 
the thermostat needs adjust-
ment. 
2. Faulty thermostat. 
3. Dirty condenser. 

1. Adjust hopper thermo-
stat temperature. 
2. Call the Donper USA 
service line to have ther-
mostat inspected and/or 
replaced. 
3. Clean the condenser. 
Make sure that the ma-
chine is completely turned 
OFF. 

Summary of Contents for BH7480







































Reviews:

No comments

Brands by name

Popular brands

Load more brands