manualshive.com logo in svg

DONPER BH7480, User Manual

Share
Download
DONPER BH7480 User Manual Download Page 17

DONPER 

USA

—USER MANUAL 

17  — COPYRIGHT DONPER USA 2015 

OPERATING IN THE STANDBY MODE: (cont’) 

To start the Standby mode, with the machine in Auto Mode on both 
sides, press and hold the Wash bu on for 

fi

ve (5) seconds (machine will 

beep 5  mes), then release. The LCD displays will now alternate be

‐

tween “00” and “bb”.  Both mixer motors will turn o

ff

 and the refrigera

‐

on system will keep the product in the cylinders refrigerated.  In this 

mode it is also necessary to make sure that the hopper cooling system 
switch is set to ON.  Not turning the hopper cooling switch on will allow 
the product in the hoppers to spoil

.    

 

 

 

 

 

 

 

 

 

 

 

 

 

To enter standby mode  you must also remove the feed tubes from 
inside the hoppers and reverse their position, as shown above. To 
do this you first remove the air caps from the top end of the feed 

 

Normal Feed Tube 

Posi on 

Standby Feed Tube 

Posi on 

Summary of Contents for BH7480







































Reviews:

No comments

Brands by name

Popular brands

Load more brands