background image

9

EN

PRO TRIM™ Single/Dual Bezel Switch Assembly Installation

 

I

If installing a single switch, be sure the hole is 
drilled on the side the switch lever will be installed.

7.  Attach the wires to the switch; red wire to the center 

terminal, green wire to the top terminal, and blue 
wire to the bottom terminal (see Figure 2).

q

r

e w

17 

Mount the Boot

q

 Boot

e

 Steering Wheel Shaft

w

 Tilt Mechanism

r

 Bezel

8.  Place the tilt mechanism in the middle position.

9.  Align the punch marks on the boot with the drilled 

holes on the metal mounting flange.

10. Install the boot onto the tilt mechanism by doing the 

following:

a.  Push down completely around the top of the boot  

to engage it on the metal mounting flange. 

b.  Use a rolling motion with your fingers over the 

corners to ensure that the boot face is resting flush 
on the metal mounting flange. There is an undercut 
inside the boot near the face that accepts the 
edges of the metal mounting flange. 

c.  Make sure the boot is flush against the metal 

mounting flange before proceeding. 

d.  Do not attach the boot to the plastic bezel at this 

time. 

18 

Mount the Switch Assemby

11.  Place the tilt mechansim in the full up position.

12. Hold the switch assembly in place against the boot 

face. 

13. For the SH91800 tilt unit, secure the switch assembly 

with two 8/32 x 1/2 in. self-tapping screws 
(provided). Proceed to step 20.

14. Insert one 5/8 in. flat-head screw (provided) into 

the right side through the assembly switch bracket, 
boot, and drilled hole of the metal mounting flange. 
Do not tighten at this time.

15. While holding the screw in place, lift the boot 

from the bottom right side and thread a locknut 
(provided) onto the flat-head screw. Do not tighten 
at this time.

16. Place the tilt mechanism in the full down position.

17.  Repeat steps 14 and 15 for the left side screw.

18. Place the tilt mechanism in the middle position.

19. Align the switch assembly bracket to the steering 

wheel shaft and boot. Tighten the screws as follows:

a.  With the tilt mechanism in the full up position, pull 

the rubber boot up from the bottom at the right 
side and tighten the locknut.

b.  With the tilt mechanism in the full down position, 

pull the rubber boot up from the bottom on the 
left side and tighten the locknut.

Summary of Contents for PRO TRIM PT1000-2

















Reviews: