Domel AZ 108 Instructions Manual Download Page 39 | Manualshive

Page: 39 / 50

Domel AZ 108 Instructions Manual Download Page 39

AZ motor

Edition 4

Instructions for bearings replacement

39

All bonding screws of motors AZ 108, AZ 150 and AZ 220 have to
be secured against the unscrewing with appropriate glue. It is
recommended to use glue Loctite 243. Apply the glue on bonding
screw thread.

When screwing bonding screws you should screw them diagonally.

Remove centering tube from rotor shaft. Remove two eye bolts from the stator support. Fasten
the stator  support, motor  housing and  flange with 4 bonding screws (pos.  19 for  motors AZ
108,  AZ  150  and  AZ  220  or  pos.  16  for  motors  AZ  84).  Under  the  screw  head  the  washer
(pos. 20) has to be mounted (for motors AZ 108, AZ 150, AZ 220). Screw the bonding screws
with sufficient tightening torque by using torque wrench (m). Tightening torque  for bonding
screws  (pos.  19  -  AZ  108,  AZ  150,  AZ  220)  is  6  Nm  while  tightening  torque  for  bonding
screws (pos. 16 - AZ 84) is 13 Nm.

19 (INBUS 5 mm)

20

«
...
37
38
39
40
41
...
»

Summary of Contents for AZ 108



















































Reviews:

No comments