background image

 

5

Method of operation 

–  Use the Hedge Trimmer only in good light and visibility.    During 

cold seasons beware of slippery or wet areas, ice and snow (risk 
of slipping).    Always ensure a safe footing. 

–  Do not overreach or stand on unstable support.  Keep good 

footing and balance at all times. 

–  Keep both feet on the ground. 

–  Never stand on a ladder and the Hedge Trimmer. 

–  Never climb up into trees to perform cutting operation with the 

Hedge Trimmer. 

– 

DANGER-CUT HAZAARD-KEEP HANDS AWAY FROM BLADES.

 

Don’t feed twigs or other material to be cut into the blade with 
your hands or reach over the moving blade to pick up clippings.   
Never grasp the exposed cutting blades or cutting edges when 
picking up or holding the tool.   

CAUTION

-Blade may coast after 

its turned off. 

– 

KEEP HANDS AND ALL PARTS OF BODY AWAY

 

from blade.  

The edges are sharp and can cause injury even when the tool is 
“OFF” 

– 

BEFORE TRIMMING

, inspect areas for wires, cords, glass or 

other foreign objects which could come in contact with the blade. 

–  Keep both hands on the handles when operating a Hedge 

Trimmer.  Never grasp exposed cutting blades of Hedge 
Trimmer. 

–  Make sure engine is stopped and blades have stopped moving 

before clearing jammed material. 

–  Be aware of any and all electric lines and electric fences.    Check 

all areas for electrical lines before cutting. 

–  To reduce the risk of stumbling and loss of control, do not walk 

backward while operating the machine. 

 
 

Maintenance instructions 

–  Always stop the engine before cleaning or servicing the unit or 

replacing parts. 

– 

MAINTAIN TOOL WITH CARE.

  Keep cutting edges sharp and 

clean for best and safest performance.  Follow instructions for 
lubricating and proper maintenance. 

–  Be kind to the environment.    Operate the Hedge Trimmer with as 

little noise and pollution as possible.  In particular check the 
correct adjustment of the carburetor. 

–  Clean the Hedge Trimmer at regular intervals and check that all 

screws and nuts are securely tightened. 

–  Never service or store the Hedge Trimmer in the vicinity of open 

flames, sparks, etc. (11). 

–  Always store the Hedge Trimmer in a well-ventilated locked room 

and with an emptied fuel tank out of reach of children. 

 

 
 
 
 
 
 
 
 
 
 
 
(10) 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
(11) 

 

Observe and follow all relevant accident prevention instructions issued by the trade associations safety boad and by insurance 
companies. 
Do not perform any modifications to the Hedge Trimmer as this will risk your safety. 

 
The performance of maintenance or repair work by the user is limited to those activities as described in this instruction manual.    All other work is 
to be done by DOLMAR authorized or Factory Service Centers. 
Use only genuine spare parts and accessories supplied by DOLMAR authorized or factory service centers. 
Use of non-approved accessories and tools means increased risk of accidents and injuries.    DOLMAR will not accept any liability for accidents 
or damage caused by the use of any non-approved accessories. 
 
 

Summary of Contents for HT-2145 D
















































Reviews: