background image

5.8 

Directly assigning control addresses and/or inputs

The gateway offers you a time-saving way of assigning Dupline 
addresses directly to lighting scenes or lighting groups without having to 
switch to 

Group mode

 or 

Scene mode

. Bring up the following menu item:

S e t - u p

I n p u t s

Pressing ② or ③ takes you to the following menu:

S e l e c t

f u n c t i o n

E s c

G r : 0 2

!

O K

Press ② or ③ to select the group (“Gr”), lighting scene (“Sc”) or central 
command (“C-on”/ “C-off”) in which a change is to be made. Only those 
groups and/or scenes that have already been allocated are shown. An 
exclamation mark denotes that an address has already been assigned 
to this group. Pressing ④ selects the item and takes you to the menu in 
which the change can be made.

S e l e c t

D u p

a d d r

E s c

+

D 5

+

*

O K

assignment status

*

Currently assigned address

!

The address is already being used for a different group or scene. 
If you nevertheless select this address, the gateway deletes the 
previous assignment.

Pressing ② or ③ selects an address to be assigned to the group or scene. 
Pressing ④ saves the current choice; pressing ① takes you back to the 
previous menu without saving.

32

Doepke

Summary of Contents for DCI 4 DALI













































Reviews: