TEST
ACTION
APPLICABILITY
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Driver Airbag Squib connector(s).
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Connect the appropriate Load Tool to the Driver Airbag connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t
, read the active Airbag Control Module DTC’s.
Does the DRBIII
t
show DRIVER SQUIB 1 CIRCUIT OPEN?
All
Yes
→
Go To
3
No
→
Replace the Driver Airbag in accordance with the Service Infor-
mation.
Perform __AIRBAG VERIFICATION TEST - VER 1.
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Driver Airbag connector(s).
Disconnect the Clockspring connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Clockspring connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t
, read the active Airbag Control Module DTC’s.
Does the DRBIII
t
show DRIVER SQUIB 1 CIRCUIT OPEN?
All
Yes
→
Go To
4
No
→
Replace the Clockspring in accordance with the Service Informa-
tion.
Perform __AIRBAG VERIFICATION TEST - VER 1.
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Clockspring connector(s).
Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connec-
tor(s).
Measure the resistance of the Driver Squib 1 Line 1 and Line 2 circuits between the
ACM Adaptor and the Clockspring connector(s).
Is the resistance below 1.0 ohm on both circuits?
All
Yes
→
Go To
5
No
→
Repair open or high resistance in the Driver Squib 1 Line 1 or
Line 2 circuits.
Perform __AIRBAG VERIFICATION TEST - VER 1.
45
AIRBAG
DRIVER SQUIB 1 CIRCUIT OPEN —
Continued
Summary of Contents for Ram 2004
