TEST
ACTION
APPLICABILITY
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Driver Airbag Squib connector(s).
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Connect the appropriate Load Tool to the Driver Airbag connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t
, read the active Airbag Control Module DTC’s.
Does the DRBIII
t
show DRIVER SQUIB 2 CIRCUIT OPEN?
All
Yes
→
Go To
3
No
→
Replace the Driver Airbag in accordance with the Service Infor-
mation.
Perform __AIRBAG VERIFICATION TEST - VER 1.
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Clockspring connector.
Disconnect the Clockspring connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Clockspring connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t
, read the active Airbag Control Module DTC’s.
Does the DRBIII
t
show DRIVER SQUIB 2 CIRCUIT OPEN?
All
Yes
→
Go To
4
No
→
Replace the Clockspring in accordance with the Service Informa-
tion.
Perform __AIRBAG VERIFICATION TEST - VER 1.
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Clockspring connector(s).
Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connec-
tor(s)
Measure the resistance of the Driver Squib 2 Line 1 and Line 2 circuits between the
ACM Adaptor and the Clockspring connector.
Is the resistance below 1.0 ohm on both circuits?
All
Yes
→
Go To
5
No
→
Repair open or high resistance in the Driver Squib 2 Line 1 or
Line 2 circuits.
Perform __AIRBAG VERIFICATION TEST - VER 1.
57
AIRBAG
DRIVER SQUIB 2 CIRCUIT OPEN —
Continued
Summary of Contents for Ram 2004
