45
≥
Command name:
+CGEQMIN=[parameter]
[M]
･
Outline
This command registers the reference value to judge whether the system permits QoS (Quality of service) reported from the network at establishment of
the packet communication.
You can specify four setting patterns described in the command execution example below.
･
Format
+CGEQMIN=[<cid>[,,<Maximum bitrateUL>[,<Maximum bitrate DL>]]]
･
Explanation of parameters
<cid>
※
: 1 to 10
<Maximum bitrate UL>
※
: None (default) to 2048
<Maximum bitrate DL>
※
: None (default) to 7232
※
<cid> is a number used to manage an access point name (APN) for packet communication, which is registered in the FOMA terminal.
<Maximum bitrate UL> and <Maximum bitrate DL> are used to specify the maximum baud rates (kbps) for upload and download between the FOMA
terminal and base station. “None” (default) accepts all baud rates, however, you may not be able to establish packet communication if you specify
2048 and 7232 because the baud rate less than these values are not accepted.
･
Operation at omission of parameters
+CGEQMIN=
: Sets all the <cid> contents to the default.
+CGEQMIN=<cid>
: Sets the specified <cid> to the default.
･
Command execution example
You can specify only the following four setting patterns:
(The setting in (1) is defined in each cid as the default.)
(1)Command that accepts all the baud rates for both upload and download (cid=2)
AT+CGEQMIN=2
OK
(2)Command that accepts 2048 kbps for upload and 7232 kbps for download (cid=3)
AT+CGEQMIN=3,,2048,7232
OK
(3)Command that accepts 2048 kbps for upload and all baud rates for download (cid=4)
AT+CGEQMIN=4,,2048
OK
(4)Command that accepts all baud rates for upload and 7232 kbps for download (cid=5)
AT+CGEQMIN=5,,,7232
OK
※
This command, which is a setting command, is not stored in the nonvolatile memory written by [&W], and is not reset by [&F] and [Z], either.
≥
Command name:
+CGEQREQ=[parameter]
[M]
･
Outline
This command sets QoS (Quality of service) to be requested to the network at dialing of the packet communication.
You can specify only one setting pattern described in the command execution example below, which is set as the default.
･
Format
+CGEQREQ=[<cid>]
･
Explanation of parameter
<cid>
※
: 1 to 10
※
<cid> is a number used to manage an access point name (APN) for packet communication, which is registered in the FOMA terminal.
･
Operation at omission of parameter
+CGEQREQ=
: Sets all the <cid> contents to the default.
+CGEQREQ=<cid>
: Sets the specified <cid> to the default.
･
Command execution example
You can specify only the following one pattern:
(This setting is defined in each cid as the default.)
(1)Command that requests a connection at arbitrary speed NW sets (cid=3)
AT+CGEQREQ=3
OK
※
This command, which is a setting command, is not stored in the nonvolatile memory written by [&W], and is not reset by [&F] and [Z], either.
≥
Command name:
+CLIP
･
Outline
The result for “AT+CLIP=1” is displayed in the following format:
+CLIP: <number> <type>
･
Command execution example
AT+CLIP=1
OK
RING
+CLIP: "09012345678",49
