Docomo FOMA D905I, Manual

Page: 427 / 513

425 Appendix/External Devices/Troubleshooting
Example of Error messages
Error Message
Main error messages displayed on the FOMA terminal are shown in the alphabetical order as follows:
･
The “(number)” or “(XXX)” in error messages is a code used to distinguish the error sent from the i-mode Center.
Address is not valid. (451)
Make sure if the address is correct.
A Network error has occurred.
Select
OK
and terminate the GPS
function.
Authentication type is not
supported. (401)
The authentication type is not
supported and connection to the
specified i-mode sites or websites
are disabled.
Cannot execute because of
other tasks.
Please retry after the running
function is finished.
Caution ! This SMS includes
Phone Nos. or URLs.
Be careful if you do not
recognize the sender.
In case
Message scan
is set to
Valid
in
Scanning Setting, when received
SMS messages contain the phone
number or URL, this message
appears when the SMS message is
tried to be displayed first.
Certificate is rejected.
(tampered)
The site certificate is altered.
Connection is suspended.
Check address.
Failed to transmit SMS. Make sure if
the address is correct.
Check address.
The mail address in the mail group
contains error or no mail address is
entered.
Check the mail address.
Check SMS center setting.
SMS setting at
SMSC
is incorrect.
☛
P208
Connection failed.
Failed to connect to the i-mode
Center. Please move to another
location with good radio reception
and retry.
Connection failed. (403)
Failed to connect due to some cause
such as rejection of connecting.
Connection failed. (503)
Failed to connect because of the
maintenance of the server or
congestion of the line.
Please retry after a while.
Connection failed. (562)
Failed to connect to the i-mode Center.
Please move to another location with
good radio reception and retry.
Connection interrupted.
Please move to another location with
good radio reception and retry. If the
error persists, try again later.
Content length exceeds
maximum size for i-motion.
Reception was suspended because
the data exceeded the maximum size
when downloading i-motion data.
Continue using i-
α
ppli and
transmit data?
i-
α
ppli tried to transmit again after
the message
Data transmission is
frequent. Continue transmission?
was
displayed.
Corrupted data. Restore
default setting?
The data contains error. Select
Yes
to
return to the default setting. Starting
is unavailable without restoring the
default setting.
Data in IC card is full. Unable
to download. Delete service?
New Osaifu-Keitai compatible i-
α
ppli
cannot be downloaded if Osaifu-Keitai
compatible i-
α
ppli registered already is
deleted because the data in IC card is
full. Select
Yes
and the Osaifu-Keitai
compatible i-
α
ppli which saved already
appears.Delete i-
α
ppli software
registered already until free disk space
required for IC card is secured.
･
In case the message
IC card memory
full
.
Delete unwanted item.
appears
on the list, select i-
α
ppli to be
deleted. When highlighting i-
α
ppli, in
case
Start
is shown in the upper right
part of the guide row, select after
activating i-
α
ppli by pressing
p
and delete the data in IC card.
･
In case the message
xxxx byte need
to delete
. appears on the list, the
data size used in IC card is shown
for i-
α
ppli respectively. Activate
i-
α
ppli to be deleted and delete the
data in IC card.
Data in IC card is full. Unable
to run.
Osaifu-Keitai compatible i-
α
ppli
cannot be downloaded because the
data in IC card is full. Select
Yes
and
the i-
α
ppli list to be deleted appears.
Delete Osaifu-Keitai compatible
i-
α
ppli services registered already
until free disk space required for IC
card is secured.
Data in IC card is full. Unable
to run. Delete service?
Osaifu-Keitai compatible i-
α
ppli
cannot be started because the data
in IC card is full. Select
Yes
and the
Osaifu-Keitai compatible i-
α
ppli which
registered already appears. Follow
the screen and start i-
α
ppli and then
delete the data in IC card.
Data in IC-card is full. Unable
to start.
Osaifu-Keitai compatible i-
α
ppli
cannot be started because the data
in IC card is full. Delete Osaifu-Keitai
compatible i-
α ppli services
registered already until free disk
space required for IC card is
secured.
Data in IC card is full. Unable
to update. Delete service?
Osaifu-Keitai compatible i- α ppli
cannot be updated unless Osaifu-
Keitai compatible i-
α
ppli registered
already is deleted because the data
in IC card is full. Follow the
procedure described in the message
of “Data in IC card is full. Unable to
download. Delete service?”.
Data or microSD damaged.
The microSD memory card cannot be
accessed because the data saved in
the microSD memory card or
microSD memory card has a problem.
Initialize the microSD memory card or
insert a new microSD memory card.
☛
P300, P292
Next
▲