background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Limited Warranty

 

What does your warranty cover?

 

 

Any defect in materials or workmanship when used for the intended purpose of storing 
kayaks on the side of a boat dock under normal use and conditions. 

 

The warranty is limited to the original purchaser. 

For how long after the original purchase?

 

 

One year  

What will we do?

 

 

Provide you with a replacement part at no charge for any part found defective in 
materials or workmanship. 

How do you make a warranty claim?

 

 

Please contact DockCraft Industries for a Return Material Authorization (RMA) number 
before returning items.   A shipping address will be provided at that time. 

What does your warranty not cover?

 

 

Damage from failures that occur as a result of improper assembly, failure to properly 

adjust and operate, misuse or neglect of product’s intended purpose.

 

 

Product which has been modified in any manner. 

 

Safeguards are not followed 

 

The warranty is not valid if you are not the original purchaser. 

 

Cosmetic defects 

“The DockSider”

TM

 PARTS LIST 

 

Bolt On Dock Mount Models;  Series 100

 

Remove all parts from the box and remove the dock mount from the pivot lateral by 
unwrapping the stretch wrap. 
If any parts are missing from the package (in type or quantity), do not assemble and contact 
DockCraft Industries immediately. 

Model DS100 –

 

Model WS100 -

 

  Dockside Operation

 

Waterside Operation

 

2

 

1

 

3

 

 

 

 

Page 3 of 14

 

4

 

5

 

Parts Diagram 

1 - Handle Assembly (1) 
2 - Pivot Lateral Cradle Assembly (2) 
3 - Dock Surface Mount Assembly (2) 
4 - SnapToggles, screws, and washers (4) 
5 - Hardware Kit (4 clevis Pins & Clips) 

Cam Buckles 

 

Latch Plates 

Summary of Contents for The DockSider 100 Series















Reviews: