32
LUBRICATION CHART
LUBRICATION
LOCATION DESCRIPTION AND
SERVICE RECOMMENDATIONS
RECOMMENDED
LUBRICANT
LUBRICATION
INTERVAL*
LUBRICATION
POINT NO.
High quality, rust and oxidation-inhibited,
medium hydraulic and general purpose
industrial oil.
ISO-VG Grade 68 (Formerly ASTM Grade
No. 315).
Union 76, UNAX RX 68, or equivalent.
Premium quality, multi-purpose lithium-
base, EP (extreme pressure) grease.
NLGI No. 2.
Union 76, UNOBA EP 2, or equivalent.
Saw Guide Arm Slide.
Clean and apply oil.
1
MONTHLY
Micellaneous: Vise Slide, Hinges, Pivot Points,
Component Parts, Unpainted Surfaces, etc.
To ensure
function and maintain appearance while reducing wear,
corrosion, rust, etc. Apply when and where needed in
amounts required.
6
MONTHLY
2
7
4
Index Vise Movable Jaw Ways.
Four (4) grease fittings.
Saw Guide Adjustment Screws.
Clean and apply oil.
Idler Bandwheel Slide.
Two (2) grease fittings.
MONTHLY
6 MONTHS
Electric Motors.
Oil cup and/or grease fittings.
Lubricate (if any) per manufacturer's recommendations.
10
Premium quality, saw band coolant and
lubricant.
DoALL cutting fluids and/or oils.
Coolant Reservoir.
20 gallon (75.7 liter) capacity. Drain,
clean and refill whenever coolant becomes undesireable for
further use. Clean the mesh screen at the same time.
9
AS REQUIRED
* Lubrication intervals are based on a 8-hour day, 40-hour week.
Lubricate more often with heavier use.
Hydraulic System.
Ten (10) gallon (37.8 liter) capacity.
Check fluid level daily and keep the reservoir full. Drain,
change the filter element and refill after the 1st month;
every six (6) months thereafter.
CHECK DAILY/
AS REQUIRED
8
INSERT CHANGE
MONTHLY
Idler Bandwheel Bearing.
One (1) grease fitting.
12
5
Sensing Arm.
Clean and apply oil.
6 MONTHS
Transmission.
18 quart (17.0 liter) capacity. Drain and refill
every six (6) months.
Do not overfill.
High quality, 4EP (extreme pressure) multi-
purpose gear oil.
Mobil Gear (629-YC1F4), Union Extra duty
NL Gear Lube.
S.A.E Grade No. 90.
11
MONTHLY
3
Index Vise Bearing Rails (5' Index Option).
Four (4)
grease fittings.
CHECK DAILY/
AS REQUIRED
Band Mist Lubricator (Optional).
Keep reservoir filled
and hoses clear.
Contact your DoALL sales representative
for the best oils and/or fluids for your
application.
DoALL cutting fluids and/or oils (AL-2000).
CHECK DAILY/
AS REQUIRED
Multi-purpose automatic transmission
fluid.
General Motors Dexron III, or equivalent.
13
Summary of Contents for C-4100NC
