DoAll C-4100NC, Instruction Manual

Page: 24 / 49

20
12. FIXED CLAMP (F12). Push this button to clamp
the fixed vise jaws during "MANUAL" operation
(this function is latched on). The LED above the
button shines only when clamping force is applied.
When the band drive motor is running, the fixed
vise jaws must be clamped before the saw head
will descend.
13. INDEX REV (Reverse) (F13). Pushing this button
causes the index vise to move away from the saw
band (toward the rear of the feed conveyor) during
"MANUAL" operating mode. Releasing the button
stops index motion. The LED above the button shines
when the index reverse solenoid is energized.
• When the INDEX REV button is pushed, the index
creeps slowly for about two (2) seconds, then
accelerates to full speed.
• The index will not move if the fixed vise jaws and
index vise jaws are both clamped. The Display will
flash: BOTH VISES CLAMPED.
14. INDEX FWD (Forward) (F14). Pushing this button
during "MANUAL" operation moves the index vise
toward the saw band. Releasing the button stops
index vise motion. The LED shines when the index
forward solenoid is energized.
• When the INDEX FORWARD button is pushed, the
index will creep slowly for about two (2) seconds,
then accelerate to full speed.
• The index will not move if the fixed and index vise
jaws are clamped.
15. LOAD PREP (F15). This button is used during
"MANUAL" operating mode to prepare the machine
for material loading. Pushing this button starts a
cycle which: (a) Moves the saw head completely
upward; (b) Opens the index vise jaws and fixed vise
jaws fully; (c) Moves the index completely forward
(toward the saw band).
• The LED above the LOAD PREP button shines
when the function is in process and goes out when
completed.
16. CREEP SPEED (F16). This screen is used to set the
positioning speed (creep speed) of the index vise.
This button is used during "MANUAL" operating
mode to increase or decrease index rate of travel
along the index section when the INDEX FWD or
INDEX REV buttons are activated.
• When creep speed is active (LED is lit), the index
vise does not go to full speed after two (2) seconds.
It will always stay at the creep speed setting.
• A password must be entered to clear Job s or Dones .
The password is the same as the model number of
the saw (i.e. 305, 3300, 4100, 650, 820). To clear
the desired items: (a) Press the 0/INS key and/or the
"UP" or "DOWN" arrows key to move to the password
area; (b) Enter the password, press ENTER; (c) A
message appears prompting the operator to use the
arrow keys to select clearing the “Jobs to 0” or the
“Dones to 0”. Use the arrow keys to make a choice.
A cursor will appear directly to the left of the choice.
(d) Press the "+/-" key to start the operation.
Clearing Jobs to 0 COMPLETELY clears the
contents of the Job Library.
8. (F8). This function button is not used and is available
for future options.
Function Keys -- Lower Left Operator Work Station.
9. INDEX OPEN (F9). This button controls the opening
movement of the index vise jaws during "MANUAL"
operation. Operation options: (a) If the saw head
is not completely raised, pushing and holding this
button opens the index vise jaws; (b) Releasing
the button stops vise jaw movement; (c) If the vise
was clamped, the LED above the button will go out
when this button is pushed. Take care to prevent
mechanical interference with the fixed vise
jaws.
• If the saw head is not completely raised when the
button is pushed, the vise will open only a small
amount (normally enough to allow movement of
the stockpiece).
10. INDEX CLAMP (F10). Push this button during
"MANUAL" operation to clamp the index vise
jaws (this function is latched on). The LED above
the button shines only when clamping force is
applied.
11. FIXED OPEN (F11). This button controls opening
movement of the fixed vise jaws during "MANUAL"
operation. It functions similarly to the INDEX OPEN
button described above.
OPERATOR WORKSTATION (Continued....)