background image

Polisher

18

ENG

• 

continuous operation of the polisher shall not exceed 30 minutes followed by a break 
of minimum 20 minutes; 

4.  Avoid ingress of dust to the polisher air vents, which can cause its overheating. Watch 

the polisher body temperature near the gear unit and motor. It shall not exceed 60°C 
and 50°C respectively. In case of overheating, let the polisher work idle for 30-60 s, and 
then turn it off to cool and remove dust.

5.  Upon the polisher turning off wait until the head stops completely before to place the 

tool on any surface.

Rotation speed governor 

Speed governor sets the necessary number of revolutions, selected depending on 

material to be processed. When operating the polisher you can smoothly adjust the spindle 
speed within the range from 600 to 3600 rpm. The rotation speed can be set with rotaton of 
governor wheel within 6 positions Fig. 5.

«MIN» position corresponds to the minimum spindle speed, and «MAX» position - to 

the maximum spindle speed. When working at low speed for a long time (approx. 15 min.), 
the machine shall be cooled down for 3 minutes. To do this, set the maximum number of 
revolutions and leave the machine idle. 

*The rotation speed is preliminary and may differ to a small degree from the specified 
in this manual.

ON/OFF 

Press the power button (1) to turn on. Release the button to stop. Press the power button 

(1) and fix it with the lock button (2) for continuous operation. To turn off if in the continuous 
mode press the power button (1) and then release it. 

10. STORAGE

Keep the tool, operating manual and accessories in their original packaging. In this case, 

all the necessary information and parts will always be at hand. Always store the tool in a dry 
place far away from children.

11. DISPOSAL

Do not dispose electric tools together with household wastes! Store and dispose the out-

of-order electric tools separately in compliance with environmental legislation.

Fig. 4

Fig. 5

Summary of Contents for PM-160SP





































Reviews: