PM-160SP
17
ENG
To avoid serious injury make sure the polishing head is firmly fixed on the backing
pad, and strings are removed.
8. SWITCHING ON FOR THE FIRST TIME
1. Unpack the tool and visually inspect scope of supply to make sure that there are no
external mechanical damages.
2. Attention! If during transportation ambient temperature was lower than +5°C, it is
necessary to leave the machine in a room with temperature r5° to +35°С and
relative humidity not exceeding 80% for at least four hours prior to further operations.
In case condensate is created on parts and assemblies of the machine, its operation or
further preparation for operation is prohibited until the condensate completely dries.
3. Check and securely fix an additional handle.
4. Install and secure the replacement tools properly.
5. Turn on the polisher and let it work without load about 3 minutes. You may observe
increased sparking of brushes for some time, because they are grinding to collector, and
from ventilation slots of body small parts of grease may emerge.
6. Check the power and lock buttons functioning.
7. If the test was successful, you can start works. Otherwise, consult your dealer or
service center.
9. RECOMMENDATIONS FOR USE
General recommendations
1. Read “SAFETY MEASURES”, «MAKEREADY» and «THE FIRST USE» sections carefully,
and follow the requirements stated there.
2. Before to start operation check the polisher functionality:
•
visually inspect the electric tool for the absence of external mechanical damage;
•
fit an additional handle, if not installed, check its reliable fastening;
•
test the polisher idle operation for 10 seconds.
3. Remember:
•
the tool is designed for operation at ambient temperature from +5°С to + 35°С;
1
Fig. 2
Fig. 3
Summary of Contents for PM-160SP
