background image

DLM-4 ZONE

DLM-4 ZONE

Controller

Controller

 10

 11

6. Connections Continued...

Only use DLM-4 Zone Controller cables
Connect the cable going from Zone 1 to the first ballast to be 
connected. (Refer to image above) 
Use the supplied “T” connector and short cable so that the first 
cable can continue on to be connected to the next “T” (ballast) 
to be connected. Repeat this process until all of the fixtures are 
connected to the zone. 

*NOTE: 

Repeat process for the other zones 

to be used.

*NOTE: 

The temperature sensors can be connected 

ANYWHERE

 

within the zone communication wiring. Only (1) temperature sensor 
can be connected per zone.
If the temperature probe receives direct HID light, it can cause 
premature dimming and inaccurate (high) temperature readings. 
When positioning the temperature probes, shield them from 
exposure to direct light.
The communication cables should now be connected in a “daisy-
chain” configuration so that each ballast is looped / jumped to the 
next ballast. All ballast and the temperature sensors should be 
connected to the zones before continuing the installation.
Verify that all of the fixtures connected to the DLM-4 Zone 
Controller have been set to operate using the External control. Turn 
the selector switch on the side of each of the ballast to the correct 
position to allow the DLM-4 Zone Controller to control the ballast. 

*NOTE: 

If the ballast selector switch is NOT positioned to allow 

External (DLM-4 Zone Controller) control, the ballast will function 
manually, without control.

DO NOT CONNECT THE POWER CABLES ON THE BALLAST UNTIL 

THE 

DLM-4 ZONE ZONE WIRING AND SET-UP IS COMPLETE. 

Once all of the zone cables are connected, you should now be able 
to verify the temperature sensors are sending data back to the main 
DLM-4 Zone Controller unit. Connect the DLM-4 Zone Controller 
to power and confirm the temperature sensors are connected by 
viewing the Zone Status screen. (After the unit starts, press the 
Enter button to display the Zone Status screen)
The final step is to continue to choose the settings for the DLM-4 
Zone Controller. The following section will explain how to customize 
the DLM-4 Zone Controller Zone for your set-up. 

1
2

3

4

5

6

7

8

9

10

*NOTE: 

The temperature sensor for each zone can be connected

 

ANYWHERE 

along the zone cabling. The same type cable splitter is 

used to connect the temperature sensor inline with the ballast. The 
signal from the temperature sensor communicates with the DLM-4 
Zone Controller through the same cables that communicates with the 
fixtures.

Summary of Contents for DLM-4 ZONE




















Reviews: