DKS 9024-081 Installation And Owner'S Manual Download | Manualshive

Page: 6 / 44

background image

9024-066-A-1-15

3

Slide Gate Requirements

The operator is intended for installation only on gates used for vehicles.

Pedestrians must be supplied with a separate

access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that
persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.
(ref. UL 325 58.8.4.b)

All openings of a horizontal slide gate are
guarded or screened from the bottom of the gate to
a minimum of six (6) feet (1.83 m) above the ground
to prevent a 2 1/4 inch (57.2 mm) diameter sphere
from passing through the openings anywhere in the
gate and in that portion of the adjacent fence that the
gate covers in the open position.
(ref. ASTM F2200-11a, 6.1.2)

Note: Install
screened wire
mesh to a
non-compliant
gate

AND

non-compliant
adjacent fence
that covers
open gate
position
(See above).

Note: A filler post or barrier
may need to be installed in the
gap area to reduce the distance
to 2 1/4 inches

or less

.

A contact sensor should be
installed in this area for
safety. (See on next page
and page 28).

A gap, measured in the horizontal plane parallel to

the roadway, between a fixed stationary object

nearest the roadway (such as a gate support post)

and the gate frame when the gate is in either the

fully open position or the fully closed position,

shall not exceed 2 1/4 inch (57.2 mm).

(ref. ASTM F2200 6.1.4)

Closed Gate

2 1/4” maximum gap area

High Risk of Entrapment Area

High Risk of Entrapment Area

X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X

X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X

X X X

X X X

X X X

X X X

X X X

X X

X X X

X X X

Adjacent fence that covers open gate position.

72” (6 ft) minimum

6 ft minimum

Non-compliant openings

wider than 2 1/4”.

Less than 2 1/4”

Screened Wire Mesh

Compliant openings

less than 2 1/4”.

Gate Support Post

Gate Frame

Gate Frame and Adjacent Fence Area

Gate Frame and Adjacent Fence Area

A

Illustrations not to scale.

Gates shall be designed, constructed and

installed to not fall over more than 45

degrees from the vertical plane, when a gate

is detatched from the supporting hardware.

Guide

Rollers

Fall Over Bracket

«
...
4
5
6
7
8
...
»

Summary of Contents for 9024-081













































Reviews:

No comments

Related manuals for 9024-081

Brand: WORKMASTER Pages: 28

Brand: Edlund Company Pages: 2

Brand: Whisper Drive Pages: 44

Brand: quiko Pages: 2

PowerLIft CS110MYQ

Brand: Chamberlain Pages: 28

Brand: CAME Pages: 24

Brand: Delton Pages: 19

Brand: GSM Pages: 13

Brand: Dea Pages: 56

Brand: DACE Pages: 27

Brand: MPC Pages: 8

Brand: Beninca Pages: 9

cyborg Panther 1200

Brand: Accessmatic Pages: 60

Brand: Accessmatic Pages: 48

Brand: Life Pages: 10

Brand: V2 ELETTRONICA Pages: 42

Brand: V2 ELETTRONICA Pages: 92

Brand: Craftsman Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands