manualshive.com logo in svg

Ditch Witch SK500, Operator'S Manual

The Ditch Witch SK500 Operator's Manual is essential for proper operation of your equipment. Download the manual for free from manualshive.com to ensure you have all the information needed to efficiently use and maintain your SK500. Get your copy today and keep your equipment running smoothly.

Share
Download
background image

Transport - 38

SK500 Operator’s Manual

Haul

CMW

Unload

1.

Lower trailer or ramps.

2.

Remove tiedowns.

3.

Open fuel shutoff valve (shown).

4.

Start engine.

5.

Pull lift arm control to raise mount plate (and 
attachment) off ground, but keep it low.

6.

Slow engine to low throttle and slowly back unit 
down trailer or ramps.

Unhitch Trailer

1.

Stop tow vehicle and trailer on level ground. 

2.

Put manual transmission into first or reverse gear or automatic transmission into park. Turn off ignition. 
Set parking brake.

3.

Block trailer wheels.

4.

Reverse “Hitch Trailer” steps on page 35 to unhitch trailer from tow vehicle.

Crushing weight. If load falls or moves it could kill or crush you. Use 

proper procedures and equipment or stay away.

NOTICE: 

 

•

Load and unload trailer on level ground.

•

Attach trailer to vehicle before loading or unloading.

NOTICE: 

If unloading from tilt-bed trailer, be 

prepared for trailer to tilt.

t05om02

9

c.eps

Summary of Contents for SK500












































































Reviews:

No comments

Related manuals for SK500

Brands by name

Popular brands

Load more brands