Ditch Witch SK500 Operator'S Manual Download Page 16

Page: 16 / 75

SK500 Operator’s Manual

Safety - 15

Emergency Procedures

CMW

Emergency Procedures

Before operating any equipment, review emergency procedures and check that all safety precautions have
been taken.

Electric Strike Description

When working near electric cables, remember the following:

•

Electricity follows all paths to ground, not just path of least resistance.

•

Pipes, hoses, and cables will conduct electricity back to all equipment.

•

Low voltage current can injure or kill. Almost one-third of work-related electrocutions result from
contact with less than 440 volts.

Most electric strikes are not noticeable, but indications of a strike include:

•

power outage

•

smoke

•

explosion

•

popping noises

•

arcing electricity

If any of these occur, assume an electric strike has occurred.

EMERGENCY SHUTDOWN

- Turn ignition switch to STOP.

Summary of Contents for SK500












































































Search results

Summary of Contents for SK500

Reviews:

Related manuals for SK500

Brands by name

Popular brands

Ditch Witch SK500, Operator'S Manual

Search results

Summary of Contents for SK500

Reviews:

Related manuals for SK500

Brands by name

Popular brands