background image

 

Important Information 
 

This manual complies with the standards and directives mentioned in the EN 
DIN 61010-1 Norm. IQ, OQ and PQ documents are available on request. 

 
 
The systems are provided with a high-precision self-optimising 
temperature controller. Due to the self-optimisation it might oc-
cur that the set temperature is exceeded in individual cases.  
 
Please note, that by heating your samples dangerous gases may 
be emitted. In this case, the device must be used with an extrac-
tor hood.  
 
If the ThermoMixers are operated with a high shaking frequency, 
the vibrations of the system might transmit to the underground. 

        Please do consider this when placing the system. 

 

Contact with highly flammable liquids must be avoided. The ex-

changeable block may be hot. 
 

The ventilation of the device must not be blocked. To ensure the 

proper ventilation at all times please consider a minimum  

distance of 10 centimeter on each side of the device. 

 

Environmental conditions

 

 

The ideal area of operation of the devices is achieved at 80% relative air  

humidity  at most and  lays  b3°C -  +50°C  ambient air temperature. 

This values should not be under run or exceeded. 

 

 

Summary of Contents for HLC MHL 23



























Reviews: