background image

17

Maintenance

TO PREVENT SERIOUS INJURY  FROM 

ACCIDENTAL STARTING TURN THE POWER 

SWITCH OF THE ENGINE TO ITS “OFF” POSITION.

Wait for the engine to cool, and remove the spark plug wire 

before performing any inspection, maintenance, or cleaning 

procedures.

Spark Plug Maintenance:

1.  Disconnect spark plug wire from end of plug. Clean out debris 

from around the spark plug.

2.   Using the spark plug wrench provided, remove the spark plug.

Inspect the spark plug. If the electrode is oily, clean it using 

a clean, dry rag. If the electrode has deposits on it, polish it 

using emery paper. If the white insulator is cracked or chipped, 

replace the spark plug.

3.  When installing a new spark plug, adjust the plug’s gap to the 

specification on the technical specification chart. Do not pry 

against the electrode or the insulator, the spark plug can be 

damaged (see Figure 11).

4.  Install the new spark plug or the cleaned spark plug into the 

engine. Gasket style spark plugs should be finger-tightened 

until the gasket contacts the cylinder head, then turned about 

1/2 to 2/3 more rotation. Non-gasket-style spark plugs should 

be  finger-tightened until the plug contacts the head, then 

about 1/16 turn more.

!

WARNING

Figure 11

Spark Plug Gap

0.028”~ 0.031”

Summary of Contents for 106371





























Reviews: